mad00058bem mn101c97a, mn101c97d type mn101c97a mn101c97d MN101CF97D internal rom type mask rom flash rom (byte) 32k 64k ram (byte) 1k package (lead-free) qfn044-p-0606 a (under planning), qfp044-p-1010 f (under planning), tqfp048-p-0707b minimum instruction execution time 0.25 s (at 2.2 v to 3.6 v, 8 mhz) 0.5 s (at 1.8 v to 3.6 v, 4 mhz) * 62.5 s (at 1.8 v to 3.6 v, 32 khz) * * the lower limit for operation guarantee for ? ash memory built-in type is 2.0 v. ? interrupts reset, watchdog, external 0 to 5 , external 6 (key interrupt dedicated), timer 0 to 3 , timer 6 , timer 7 ( 2 systems), time base, serial 0 (2 systems), serial 3 , a/d conversion ? nish ? timer counter timer counter 0 : 8-bit 1 (square-wave/ 8-bit pwm output, event count, generation of remote control carrier , simple pulse width measurement, added pluse (2-bit) system pwm output) (square-wave/pwm output to large current terminal p 51 possible) clock source ................ 1/2, 1/4 of system clock frequency; 1/1, 1/4, 1/16, 1/32, 1/64 of osc oscillation clock frequency; 1/1 of xi oscillation clock frequency; external clock input interrupt source ........... coincidence with compare register 0 timer counter 1 : 8-bit 1 (square-wave output, event count, synchronous output event, serial transfer clock output) clock source ................ 1/2, 1/8 of system clock frequency; 1/1, 1/4, 1/16, 1/64, 1/128 of osc oscillation clock frequency; 1/1 of xi oscillation clock frequency; external clock input interrupt source ........... coincidence with compare register 1 timer counter 0, 1 can be cascade-connected. timer counter 2 : 8-bit 1 (square-wave output, added pluse ( 2-bit) system pwm output, pwm output, serial transfer clock output, event count, synchronous output event, simple pulse width measurement) (square-wave/pwm output to large current terminal p 52 possible) clock source ................ 1/2, 1/4 of system clock frequency; 1/1, 1/4, 1/16, 1/32, 1/64 of osc oscillation clock frequency; 1/1 of xi oscillation clock frequency; external clock input interrupt source ........... coincidence with compare register 2 timer counter 3 : 8-bit 1 (square-wave output, event count, generation of remote control carrier, serial transfer clock output) clock source ................ 1/2, 1/8 of system clock frequency; 1/1, 1/4, 1/16, 1/64, 1/128 of osc oscillation clock frequency; 1/1 of xi oscillation clock frequency; external clock input interrupt source ........... coincidence with compare register 3 timer counter 2, 3 can be cascade-connected. timer counter 6 : 8-bit freerun timer clock source ................ 1/1 of system clock frequency; 1/1, 1/128, 1/8192 of osc oscillation clock frequency; 1/1, 1/128, 1/8192 of xi oscillation clock frequency interrupt source ........... coincidence with compare register 6 timer counter 7 : 16-bit 1 (square-wave output, 16-bit pwm output (cycle / duty continuous variable), event count, synchronous output event, pulse width measurement, input capture, real time output control, high performance igbt output) (square-wave/pwm output to large current terminal p 53 possible) clock source ................ 1/1, 1/2, 1/4, 1/16 of system clock frequency; 1/1, 1/2, 1/4, 1/16 of osc oscillation clock frequency; 1/1, 1/2, 1/4, 1/16 of external clock input frequency interrupt source ........... coincidence with compare register 7 (2 lines), input capture register
mad00058bem mn101c97a, mn101c97d timer counters 7, 8 can be cascade-connected. (square-wave output, pwm input capture, pluse width measurement is possible as a 32 -bit timer.) time base timer (one-minute count setting) clock source ................ 1/1 of osc oscillation clock frequency; 1/1 of xi oscillation clock frequency interrupt source ........... 1/128, 1/256, 1/512, 1/1024, 1/4096, 1/8192, 1/16384, 1/32768, of clock source frequency watchdog timer interrupt source ........... 1/65536, 1/262144, 1/1048576 of system clock frequency ? serial interface serial 0 : synchronous type/uart (full-duplex) 1 clock source ................ 1/2, 1/4 of system clock frequency; pulse output of timer counter 1 or 2; 1/2, 1/4, 1/16, 1/64 of osc oscillation clock frequency, external clock serial 3 : synchronous type/single-master i2c 1 clock source ................ 1/2, 1/4 of system clock frequency; pulse output of timer counter 2 or 3; 1/2, 1/4, 1/16, 1/32 of osc oscillation clock frequency, external clock ? i/o pins i/o 38 common use , speci? ed pull-up resistor available, input/output selectable (bit unit) ? a/d converter 10-bit 8 -ch. (with s/h) ? special ports buzzer output, remote control carrier signal output, high-current drive port ? rom correction correcting address designation : up to 3 addresses possible ? electrical charactreistics (supply current) parameter symbol condition limit unit min typ max operating supply current idd1 fosc = 4 mhz, vdd = 3 v 0.9 1.7 ma idd2 fx = 32 khz, vdd = 3 v 4 24 a supply current at halt idd3 fx = 32 khz , vdd = 3 v, ta = 25 c 2.6 5 a idd4 fx = 32 khz , vdd = 3 v , ta = C40 c to +85 c 20 a supply current at stop idd5 vdd = 3 v , ta = 25 c 2 a idd6 vdd = 3 v , ta = C40 c to +85 c 15 a ? development tools in-circuit emulator px-ice 101c/d+px-prb101c97-tqfp048-p-0707b-m px-ice101c/d+px-prb101c97-qfp044-p-1010 (under planning)
mad00058bem ? pin assignment dmod vdd nrst , p27 xo xi mmo d osc1 osc2 vss led5, p55 rmout , led0, p50 tm0o, led1, p51 p31, key1, tm1io p30, key0, tm0io p25, irq5, clkout p24, irq4 p23, irq3 p22, irq2 p21, irq1 p20, irq0 p13 p12, sbt0a p1 1, txd0a, sbo0a p10, rxd0a, sbi0a 37 38 39 40 41 42 43 44 45 46 47 48 24 23 22 21 20 19 18 17 16 15 14 13 an7, p07 an6, p06 an5, p05 an4, p04 an3, p03 an2, p02 an1, p01 an0, p00 vref+ led4, p54 tm7o, led3, p53 tm2o, led2, p52 p32, key2, tm2io p33, key3, tm3io p34, key4, tm7io p35, key5, nbuzzer p36, key6, buzzer p37, key7 p40, sbi3 p41, sbo3, sda3 p42, sbt3, scl3 p43, rxd0b, sbi0b p44, , txd0b, sbo0b p45, sbt0b 36 35 34 33 32 31 30 29 28 27 26 25 1 2 3 4 5 6 7 8 9 10 11 12 mn101c97a mn101c97d tqfp048-p-0707b qfp044-p-1010f qfn044-p-0606a
request for your special attention and precautions in using the technical information and semiconductors described in this book (1) if any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and regulations of the exporting country, especially, those with regard to security export control, must be observed. (2) the technical information described in this book is intended only to show the main characteristics and application circuit examples of the products, and no license is granted under any intellectual property right or other right owned by our company or any other company. therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other company which may arise as a result of the use of technical information described in this book. (3) the products described in this book are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances). consult our sales staff in advance for information on the following applications: ? special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the prod- ucts may directly jeopardize life or harm the human body. ? any applications other than the standard applications intended. (4) the products and product specifications described in this book are subject to change without notice for modification and/or im- provement. at the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date product standards in advance to make sure that the latest specifications satisfy your requirements. (5) when designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions (operating power supply voltage and operating environment etc.). especially, please be careful not to exceed the range of absolute maximum rating on the transient state, such as power-on, power-off and mode-switching. otherwise, we will not be liable for any defect which may arise later in your equipment. even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (6) comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (esd, eos, thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. when using products for which damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages. (7) this book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of matsushita electric industrial co., ltd. industrial co., ltd.
|
